Paneli za ravne krovove velikih raspona

Applications
X-dekTM panels are insulated membrane covered roof panels suitable for flat roofs for all building applications except where there are low temperature internal conditions. The KS1000 X-DEK panel secures the base for final waterproof covering of the roof installed by others:
 
  • X-dek panels are insulated roof panels suitable for flat roofs roof slope > 1%
  • X-dek is the „long-span” composite roofing panel, which provides the necessary structural strength and stiffness and the required level of thermal insulation. An outer membrane is applied on site as a waterproof barrier
  • The KS1000 X-DEK panels are suitable for „Green Roof” solutions
  • The XD panels can be used as „standard” panel and as a part of steel structure „structural” panel (restraining for the rafters)

Sendvič paneli, Krovni paneli KS1000 X-DEK

  

Dimension and weight

 

KS1000 X-DEK / TR20

Sendvič paneli, Krovni paneli KS1000 X-DEK

 

 

KS1000 X-DEK / TR27

Sendvič paneli, Krovni paneli KS1000 X-DEK

 

 

KS1000 X-DEK / Steel

Sendvič paneli, Krovni paneli KS1000 X-DEK

 

 

KS1000 X-DEK / PVC

Sendvič paneli, Krovni paneli KS1000 X-DEK

 

 

d– core thickness (mm)
80
100
D– overall dimension (mm)
188
208
Weight (kg/m2), steel 0.9/0.7 mm
21,4
22,2
Weight (kg/m2), TR20
15,9
16,8
Weight (kg/m2), TR27
15,8
16,7

Product Tolerances

Cut to Length - 5 mm + 5 mm
Width - 2 mm + 2 mm
Thickness - 2 mm + 2 mm
End Square - 3 mm + 3 mm
Flatness (per meter) - 2 mm + 2 mm
 

Available Lengths

Standard lengths 2.5 to 13.5 meters. 13.5 – 15metres maximum can be supplied but are subject to a transport surcharge. All the Panels are manufactured with CUT-BACK (on bottom trapezoidal steel) the standard cut-back is 50mm, the maximum available is 630mm.
Sendvič paneli, Krovni paneli KS1000 X-DEK
Materials

Steel

Internal skin:

Hot-dipped zinc coated steel according to EN 10326:2004.
Grade S350GD+Z275 coated with Polyester 25 microns RAL 9002 – standard thickness 0.9.mm, on special request available 1.1mm.

External skin:

Hot-dipped zinc coated steel according to EN 10326:2004.
Grade S220GD+Z275 – thickness 0.7.mm galvanised steel with a 5 microns clear film conversion layer for bonding to.
Available profiles on top sheet: MiniBox or Flat.
TR20 – Bitumen impregnated glass fiber membrane suitable for multi layer torch on systems,
TR27 – Glass tissue facing suitable for mechanically fixed or fully adhered single ply PVC or EPDM membrane.
 

Insulation core

The rigid closed cell insulation core is available in the following specification:
Isophenic rigid foam – IPN (HCFC Free), nominal density of 40 kg/m3. Available nominal thickness of the core 80mm and 100mm.
 

Seals

Factory Applied Side Joint Seal

All side joints have a factory applied anti-condensation tape made of standard PE side foam.
Performance

Thermal Insulation

λ=0,022 W/mK:

Panel Thickness (mm)

R value

[(m2K)/W]

U Value

[W/m2K]

80 / Option I

4,21

0,23

80 / Option II

4,03

0,24

100 / Option I

5,12

0,19

100 / Option II

4,86

0,20

 

Biological

Kingspan panels are normally immune to attack from mould, fungi, mildew and vermin, no urea formaldehyde is used in the construction, and the panels are not considered deleterious.

Fire

Kingspan KS1000 X-DEK roof panels has been tested according to EN1365 as load bearing roof element. The ratings achieved are presented in the table below:

Panel Type

FIRE Rating

Max. bending

moment

KS1000 X-DEK 80 TR20

REI 15

6.621 kNm

KS1000 X-DEK 100 TR27

REI 15

7.725 kNm

KS1000 X-DEK 100 (steel)

REI 30

7.725 kNm

Acoustics

KS1000 X-DEK (X-dekTM) panels have acoustic parameters as below:

 

Parameters according to Type of panel EN ISO 717-1:1999

Type of panel

RA1 [dB]

RA2 [dB]

RW [dB]

KS1000 X-DEK 80/100

26

23

27

KS1000 X-DEK 80/100

TR20/TR27

25

22

26

Structural tables
 
Sendvič paneli, Krovni paneli KS1000 X-DEK
REMARKS:
ULS – Ultimate Limit State – indicated loads should be compared with factored (design) loads
SLS – Serviceability Limit State – indicated loads should be compared with characteristic(un-factored) loadsI
Maximum permissible deflection limit (SLS): L / 200
The minimum width of supports: at ends – 40mm, intermediate 120mm.
The dead load of panels is included in the above figures.
 
Sendvič paneli, Krovni paneli KS1000 X-DEK
Sendvič paneli, Krovni paneli KS1000 X-DEK
REMARKS:
The above values of loads are characteristic. For Each value individual and combined load cases with appropriate load factors and temperatures have been considered.
For Intermediate values linear interpolation may be used.
Values have been calculated using the limit state method according to EN 14509, taking imposed loads and temperature into account.
Maximum permissible deflection limit: downwards and upwards – L / 200
amin – the minimum width of end supports; bmin – the minimum width of intermediate supports
The dead load of panels is included in the above figures.
Site Installation

 

Site Handling and Installation

Typically the panels are stored in bundles crown-to-crown manner, for turning the panels (50%) there is recommended to use special vacuum-pump device with a 180° rotation unit. The equipment is called RotaBoy. The RotaBoy equipment can be obtained directly from the Manufacturer – Viavac, or can be hired from local ViaVac office or their representative. Address of the nearest office you can find at http://www.viavac.com/.
When panels are supplied with a plastic protective film this should be removed immediately after site installation. Site assembly instructions are available from the Kingspan Technical Services.
 

Sendvič paneli, Krovni paneli KS1000 X-DEK    Sendvič paneli, Krovni paneli KS1000 X-DEK

Sealants & Fillers

The panels need to be fitted as close together as possible to assure a certain airtightness. At each side joint it is necessary to apply butyl rubber sealing tape. For further panels stability, proper joint tightness and alignment, and fire-resistance of the KS1000 X-DEK panels, the stitching screws must be applied along the side lap of the panels. The stitching screws are usually applied from the bottom side of roof, however the application from the top is also possible. Recommended distance of the stitching screws are:
  • ≤ 500mm – for the applications where fire resistance is required
  • 500÷1000mm – for the applications where fire resistance is not required.

Build speed

  • Fast Build cuts site time by 100% – reduces prelims and attendance costs
  • Maximises investor/occupier trading income opportunity
  • Factory manufactured system facilitates zero defect installation and build quality

Sendvič paneli, Krovni paneli KS1000 X-DEK

Quality/Warranties

Quality and durability

Kingspan Insulated panels are manufactured from the highest quality materials, using state of the art production equipment to rigorous quality control standards, complying with ISO9001 standard, ensuring long term reliability and service life.
 

Guarantees & Warranties

Kingspan will provide external coating and product warranties and guaranties on an individual project basis.
Green roofs
Extensive roof gardens are areas of vegetation close to those found in nature and which to a great extent look after themselves and develop naturally. They require plants that are suitable to extreme conditions and offers a high capacity for regeneration. These mainly self contained areas are made up from mosses, succulents, herbs and grasses. The vegetation is left to natural conditions.
 
Intensive roof gardens can include the planting of small and medium shrubs, grassed areas and occasionally trees. They may cover whole areas at the same level, be stepped or form islands.
Because of their flexibility in layout and use they offer just as many possibilities as a traditional ground level garden. The plants used make substantial demands on the layers, and they require regular watering and feeding.
       
Sendvič paneli, Krovni paneli KS1000 X-DEK Sendvič paneli, Krovni paneli KS1000 X-DEK Sendvič paneli, Krovni paneli KS1000 X-DEK
Intensive green roof Extensive green roof Brown roof

Zatražite dodatne informacije !

Kingspan d.o.o.
Meše Selimovića br. 28
78000 Banjaluka
Bosna i Hercegovina
Tel.: +387 51 226 190
+387 65 716 921
fax. 387 51 226 191
info@kingspan.ba